API-hölje och slangstorlekstabell
Jun 02, 2026
EnligtAPI Spec 5CT(Specifikation för hölje och slangar),API-hölje och rörkallas gemensamt för Oil Country Tubular Goods (OCTG) och fungerar som kritiska komponenter för att säkerställa borrhålets strukturella integritet och tillhandahålla ledningar för vätskeproduktion; hölje används främst för att fodra borrhålet, isolera formationer med varierande tryck och förhindra borrhålskollaps, medan slangar installeras i höljet för att transportera olja och gas till ytan eller underlätta injektions- och produktionsoperationer.
Deras standardutvändiga diameter (OD) intervall är omfattande, medrör som vanligtvis täcker 1 050 tum (26,7 mm) till 4-1/2 tum (114,3 mm)ochhölje från 4-1/2 tum (114,3 mm) upp till 20 tum (508 mm), används i samband med olika stålsorter och gänganslutningar baserat på brunnsdjup och geologiska förhållanden.
API-hölje och slangstorlekstabell
Diagram för dimensioner och vikt för API-rör
| DN | O. D. | Vikt | W. T. | Avsluta bearbetning | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Inte-upprörd | Upprörd | Stålkvalitet | |||||||||||
| kopplings-gänga | kopplings-gänga | ||||||||||||
| Tum | mm | lb./ft. | lb./ft. | Tum | mm | H40 | J55 | L80 | N80 | C90 | T95 | P110 | |
| 2 3/8 | 2.375 | 60.32 | 4 | – | 0.167 | 4.24 | PU | PN | PN | PN | PN | PN | – |
| 4.6 | 4.7 | 0.19 | 4.83 | PNU | PNU | PNU | PNU | PNU | PNU | PNU | |||
| 5.8 | 5.95 | 0.254 | 6.45 | – | – | PNU | PNU | PNU | PNU | PNU | |||
| 6.6 | – | 0.295 | 7.49 | – | – | P | – | P | P | – | |||
| 7.35 | 7.45 | 0.336 | 8.53 | – | – | PU | – | PU | PU | – | |||
| 2 7/8 | 2.875 | 73.02 | 6.4 | 6.5 | 0.217 | 5.51 | PNU | PNU | – | – | – | – | – |
| 7.8 | 7.9 | 0.276 | 7.01 | – | – | – | – | – | – | – | |||
| 8.6 | 8.7 | 0.308 | 7.82 | – | – | PLB | PLB | PLBE | – | PLB | |||
| 9.35 | 9.45 | 0.34 | 8.64 | – | – | PLB | PLB | PLBE | – | PLB | |||
| 10.5 | – | 0.392 | 9.96 | – | – | PLB | PLB | PLB | – | PLB | |||
| 11.5 | – | 0.44 | 11.18 | – | – | – | – | PLB | – | ||||
| 3 1/2 | 3.5 | 88.9 | 7.7 | – | 0.216 | 5.49 | PN | PN | PN | PN | PN | PN | – |
| 9.2 | 9.3 | 0.254 | 6.45 | PNU | PNU | PNU | PNU | PNU | PNU | PNU | |||
| 10.2 | – | 0.289 | 7.34 | PN | PN | PN | PN | PN | PN | – | |||
| 12.7 | 12.95 | 0.375 | 9.52 | – | – | PNU | PNU | PNU | PNU | PNU | |||
| 14.3 | – | 0.43 | 10.92 | – | – | P | – | P | P | – | |||
| 15.5 | – | 0.476 | 12.09 | – | – | P | – | P | P | – | |||
| 17 | – | 0.53 | 13.46 | – | – | P | – | P | P | – | |||
| 4 | 4 | 101.6 | 9.5 | – | 0.226 | 5.74 | PN | PN | PN | PN | PN | PN | – |
| – | 11 | 0.262 | 6.65 | PU | PU | PU | PU | PU | PU | – | |||
| 13.2 | – | 0.33 | 8.38 | – | – | P | – | P | P | – | |||
| 16.1 | – | 0.415 | 10.54 | – | – | P | – | P | P | – | |||
| 18.9 | – | 0.5 | 12.7 | – | – | P | – | P | P | – | |||
| 22.2 | – | 0.61 | 15.49 | – | – | P | – | P | P | – | |||
| 4 1/2 | 4.5 | 114.3 | 12.6 | 12.75 | 0.271 | 6.88 | PNU | PNU | PNU | PNU | PNU | PNU | – |
| 15.2 | – | 0.337 | 8.56 | – | – | P | – | P | P | – | |||
| 17 | – | 0.38 | 9.65 | – | – | P | – | P | P | – | |||
| 18.9 | – | 0.43 | 10.92 | – | – | P | – | P | P | PLB | |||
| 21.5 | – | 0.5 | 12.7 | – | – | P | – | P | P | PLB | |||
| 23.7 | – | 0.56 | 14.22 | – | – | P | – | P | P | PLB | |||
| 26.1 | – | 0.63 | 16 | – | – | P | – | P | P | PLB | |||
| P--Plain;N-- Non-upset coupling-thread;U-- Upset coupling-thread; L--Integral | |||||||||||||
API-hölje Rörmått och viktdiagram
| DN | O. D. | Vikt | W. T. | Avsluta bearbetningsformulär | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Stålkvalitet | ||||||||||||
| Tum | mm | lb/ft | kg/m | Tum | mm | H40 | J55 | L80 | N80 | C90 | P110 | |
| K55 | T95 | |||||||||||
| 4 1/2 | 4.5 | 114.3 | 9.5 | 14.14 | 0.205 | 5.21 | PS | PS | – | – | – | – |
| 10.5 | 15.63 | 0.224 | 5.69 | – | PSB | – | – | – | – | |||
| 11.6 | 17.26 | 0.25 | 6.35 | – | PSLB | PLB | PLB | PLB | PLB | |||
| 13.5 | 20.09 | 0.29 | 7.37 | – | – | PLB | PLB | PLB | PLB | |||
| 15.1 | 22.47 | 0.337 | 9.56 | – | – | – | – | – | PLB | |||
| 5 | 5 | 127 | 11.5 | 17.11 | 0.22 | 5.59 | – | PS | – | – | – | – |
| 13 | 19.35 | 0.253 | 6.43 | – | PSLB | – | – | – | – | |||
| 15 | 22.32 | 0.296 | 7.52 | – | PSLB | PLB | PLB | PLBE | PLB | |||
| 18 | 26.79 | 0.362 | 9.19 | – | – | PLB | PLB | PLBE | PLB | |||
| 21.4 | 31.85 | 0.437 | 11.1 | – | – | PLB | PLB | PLB | PLB | |||
| 23.2 | 34.53 | 0.478 | 12.14 | – | – | – | – | PLB | – | |||
| 24.1 | 35.86 | 0.5 | 12.7 | – | – | – | – | PLB | – | |||
| 5 1/2 | 5.5 | 139.7 | 14 | 20.83 | 0.244 | 6.2 | PS | PS | – | – | – | – |
| 15.5 | 23.07 | 0.275 | 6.98 | – | PSLB | – | – | – | – | |||
| 17 | 25.3 | 0.304 | 7.72 | – | PSLB | PLB | PLB | PLBE | PLB | |||
| 20 | 29.76 | 0.361 | 9.17 | – | – | PLB | PLB | PLBE | PLB | |||
| 23 | 34.23 | 0.415 | 10.54 | – | – | PLB | PLB | PLBE | PLB | |||
| 26.8 | 39.88 | 0.5 | 12.7 | – | – | – | – | – | – | |||
| 29.7 | 44.2 | 0.562 | 14.27 | – | – | – | – | – | – | |||
| 32.6 | 48.51 | 0.625 | 15.88 | – | – | – | – | – | – | |||
| 35.3 | 52.53 | 0.687 | 17.45 | – | – | – | – | – | – | |||
| 38 | 56.55 | 0.75 | 19.05 | – | – | – | – | – | – | |||
| 40.5 | 60.27 | 0.812 | 20.62 | – | – | – | – | – | – | |||
| 43.1 | 64.14 | 0.875 | 22.22 | – | – | – | – | – | – | |||
| 6 5/8 | 6.625 | 168.28 | 20 | 29.76 | 0.288 | 7.32 | PS | PSLB | – | – | – | – |
| 24 | 35.72 | 0.352 | 8.94 | – | PSLB | PLB | PLB | PLBE | PLB | |||
| 28 | 41.67 | 0.417 | 10.59 | – | – | PLB | PLB | PLBE | PLB | |||
| 32 | 47.62 | 0.475 | 12.06 | – | – | PLB | PLB | PLBE | PLB | |||
| 7 | 7 | 177.8 | 17 | 25.3 | 0.231 | 5.87 | PS | – | – | – | – | – |
| 20 | 29.76 | 0.272 | 6.91 | PS | PS | – | – | – | – | |||
| 23 | 34.23 | 0.317 | 8.05 | – | PSLB | PLB | PLB | PLBE | – | |||
| 26 | 38.69 | 0.362 | 9.19 | – | PSLB | PLB | PLB | PLBE | PLB | |||
| 29 | 43.16 | 0.408 | 10.36 | – | – | PLB | PLB | PLBE | PLB | |||
| 32 | 47.62 | 0.453 | 11.51 | – | – | PLB | PLB | PLBE | PLB | |||
| 35 | 52.09 | 0.498 | 12.65 | – | – | PLB | PLB | PLBE | PLB | |||
| 38 | 56.55 | 0.54 | 13.72 | – | – | PLB | PLB | PLBE | PLB | |||
| 42.7 | 63.54 | 0.625 | 15.88 | – | – | – | – | – | – | |||
| 46.4 | 69.05 | 0.687 | 17.45 | – | – | – | – | – | – | |||
| 50.1 | 74.56 | 0.75 | 19.05 | – | – | – | – | – | – | |||
| 53.6 | 79.77 | 0.812 | 20.62 | – | – | – | – | – | – | |||
| 57.1 | 84.97 | 0.875 | 22.22 | – | – | – | – | – | – | |||
| 7 5/8 | 7.625 | 193.68 | 24 | 35.72 | 0.3 | 7.62 | PS | – | – | – | – | – |
| 26.4 | 39.29 | 0.328 | 8.33 | – | PSLB | PLB | PLB | PLBE | PLB | |||
| 29.7 | 44.2 | 0.375 | 9.52 | – | – | PLB | PLB | PLBE | PLB | |||
| 33.7 | 50.15 | 0.43 | 10.92 | – | – | PLB | PLB | PLBE | PLB | |||
| 39 | 58.05 | 0.5 | 12.7 | – | – | PLB | PLB | PLBE | PLB | |||
| 42.8 | 63.69 | 0.562 | 14.27 | – | – | PLB | PLB | PLB | PLB | |||
| 45.3 | 67.41 | 0.595 | 15.11 | – | – | PLB | PLB | PLB | PLB | |||
| 47.1 | 70.09 | 0.625 | 15.88 | – | – | PLB | PLB | PLB | PLB | |||
| 51.2 | 76.19 | 0.687 | 17.45 | – | – | – | – | – | – | |||
| 55.3 | 80.3 | 0.75 | 19.05 | – | – | – | – | – | – | |||
| 8 5/8 | 8.625 | 219.08 | 24 | 35.72 | 0.264 | 6.71 | – | PS | – | – | – | – |
| 28 | 41.62 | 0.304 | 7.72 | PS | – | – | – | – | – | |||
| 32 | 47.62 | 0.352 | 8.94 | PS | PSLB | – | – | – | – | |||
| 36 | 53.57 | 0.4 | 10.16 | – | PSLB | PLB | PLB | PLBE | PLB | |||
| 40 | 59.53 | 0.45 | 11.43 | – | – | PLB | PLB | PLBE | PLB | |||
| 44 | 65.48 | 0.5 | 12.7 | – | – | PLB | PLB | PLBE | PLB | |||
| 49 | 72.92 | 0.557 | 14.15 | – | – | PLB | PLB | PLBE | PLB | |||
| 9 5/8 | 9.625 | 244.48 | 32.3 | 48.07 | 0.312 | 7.92 | PS | – | – | – | – | – |
| 36 | 53.57 | 0.352 | 8.94 | PS | PSLB | – | – | – | – | |||
| 40 | 59.53 | 0.395 | 10.03 | – | PSLB | PLB | PLB | PLBE | – | |||
| 43.5 | 64.73 | 0.435 | 11.05 | – | – | PLB | PLB | PLBE | PLB | |||
| 47 | 69.94 | 0.472 | 11.99 | – | – | PLB | PLB | PLBE | PLB | |||
| 53.5 | 79.62 | 0.545 | 13.84 | – | – | PLB | PLB | PLBE | PLB | |||
| 58.4 | 86.91 | 0.595 | 15.11 | – | – | PLB | PLB | PLB | PLB | |||
| 59.4 | 88.4 | 0.609 | 15.47 | – | – | – | – | – | – | |||
| 64.9 | 96.58 | 0.672 | 17.07 | – | – | – | – | – | – | |||
| 70.3 | 104.62 | 0.734 | 18.64 | – | – | – | – | – | – | |||
| 75.6 | 112.5 | 0.797 | 20.24 | – | – | – | – | – | – | |||
| 10 3/4 | 10.75 | 273.05 | 32.75 | 48.74 | 0.279 | 7.09 | PS | – | – | – | – | – |
| 40.5 | 60.27 | 0.35 | 8.89 | PS | PSB | – | – | – | – | |||
| 15.5 | 67.71 | 0.4 | 10.16 | – | PSB | – | – | – | – | |||
| 51 | 75.9 | 0.45 | 11.43 | – | PSB | PSB | PSB | PSBE | PSB | |||
| 55.5 | 82.59 | 0.495 | 12.57 | – | – | PSB | PSB | PSBE | PSB | |||
| 60.7 | 90.33 | 0.545 | 13.84 | – | – | – | – | PSBE | PSB | |||
| 65.7 | 97.77 | 0.595 | 15.11 | – | – | – | – | PSB | PSB | |||
| 73.2 | 108.93 | 0.672 | 17.07 | – | – | – | – | – | – | |||
| 79.2 | 117.86 | 0.734 | 18.64 | – | – | – | – | – | – | |||
| 85.3 | 126.94 | 0.797 | 20.24 | – | – | – | – | – | – | |||
| 11 3/4 | 11.75 | 298.45 | 42 | 62.5 | 0.333 | 8.46 | PS | – | – | – | – | – |
| 47 | 69.94 | 0.375 | 20.24 | – | – | – | – | – | – | |||
| 54 | 80.36 | 0.435 | 8.46 | – | – | – | – | – | – | |||
| 60 | 89.29 | 0.489 | 9.53 | – | – | – | – | – | – | |||
| 65 | 96.73 | 0.534 | 11.05 | – | – | – | – | – | – | |||
| 71 | 105.66 | 0.582 | 14.42 | – | – | – | – | – | – | |||
| 13 3/8 | 13.375 | 339.73 | 48 | 71.43 | 0.33 | 8.38 | PS | – | – | – | – | – |
| 54.5 | 81.1 | 0.38 | 9.65 | – | PSB | – | – | – | – | |||
| 61 | 90.78 | 0.43 | 10.92 | – | PSB | – | – | – | – | |||
| 68 | 101.19 | 0.48 | 12.19 | – | PSB | PSB | PSB | PSB | PSB | |||
| 72 | 107.15 | 0.514 | 13.06 | – | – | PSB | PSB | PSB | PSB | |||
| 16 | 16 | 406.4 | 65 | 96.73 | 0.375 | 9.53 | PS | – | – | – | – | – |
| 75 | 111.61 | 0.438 | 11.13 | – | PSB | – | – | – | – | |||
| 84 | 125.01 | 0.495 | 12.57 | – | PSB | – | – | – | – | |||
| 109 | 162.21 | 0.656 | 16.66 | – | P | P | P | – | P | |||
| 18 5/8 | 18.625 | 473.08 | 87.5 | 130.21 | 0.435 | 11.05 | PS | PSB | – | – | – | – |
| 20 | 20 | 508 | 94 | 139.89 | 0.438 | 11.13 | PSL | PSLB | – | – | – | – |
| 106.5 | 158.49 | 0.5 | 12.7 | – | PSLB | – | – | – | – | |||
| 133 | 197.93 | 0.635 | 16.13 | – | PSLB | – | – | – | – | |||
| P--Vanlig;S--Korttråd;L--Långtråd;B--Strävtråd;E--Extrem tråd | ||||||||||||
Längdintervallstabell
API 5CT klassificerar rörlängder i tre "intervall" för att matcha borrningshöjder.
| Räckviddsklass | Slanglängd (ft/m) | Höljes längd (ft/m) | Industrikonventionen |
| Område 1 (R1) | 20.0 - 24.0 (6.10 - 7.32) | 16.0 - 25.0 (4.88 - 7.62) | Används sällan |
| Område 2 (R2) | 28.0 - 32.0 (8.53 - 9.75) | 25.0 - 34.0 (7.62 - 10.36) | Den vanligaste standarden |
| Område 3 (R3) | 38.0 - 45.0 (11.58 - 13.72) | 34.0 eller mer (10.36+) | För djupa eller ERD-brunnar |
OCTG hölje och rör Stålkvaliteter och mekaniska egenskaper
Stålkvaliteter bestämmer draghållfastheten, kollapsmotståndet och lämpligheten för korrosiva miljöer.
| Grupp | Vanliga betyg | Min. Avkastningsstyrka (psi) | Servicemiljö |
| Grupp 1 | H40, J55, K55, N80 | 40k - 80k | Allmänna/grunda brunnar, icke-frätande |
| Grupp 2 | L80, C90, T95, C110 | 80k - 110k | Sur service (H2S)/ Kontrollerad avkastning |
| Grupp 3 | P110 | 110k | Djupa,-högtrycksbrunnar |
| Grupp 4 | Q125 | 125k | Extremt djup och tryck |
Kabel- och slanganslutning och gängtyper
Detta definierar hur rören är sammanfogade och deras tätningsförmåga.
| Rörtyp | Förkortning | Fullständig beskrivning | Nyckelfunktioner |
| Slang | NUE | Inte-upprörd | 10 runda gängor (föråldrad/sällsynt) |
| EUE | Extern upprördhet | Smidda upprörda ändar(Standard/Starkast) | |
| IJ | Integral skarv | Spolanslutning för snäva spelrum | |
| Hölje | STC | Kort rund tråd | Kort gänga, 8-rund (lågt tryck) |
| LTC | Lång rund tråd | Lång tråd, 8-rund (bättre spänning) | |
| BTC | Buttress tråd | Trapetsformad tråd(Branschstandard) | |
| Allmän | Premie | Gastäta- anslutningar | Icke-API-gängor för gas-tät försegling |
API-hölje och slanginspektion och testning (NDT):
Hydrostatiskt test:Krävs för varje led för att verifiera tryckintegriteten.
Drifttest:Säkerställer att en dorn i standard-storlek kan passera genom röret.
Icke-förstörande undersökning:Testning med ultraljud (UT), magnetisk partikel (MPI) eller virvelström.
API-hölje och rörfabrik

utrustning för testning av tubulära varor för oljeland

höljesrörcertifikat

GNEE OCTG utbud
Standard och kvaliteter: API 5CT J55 / K55, N80-1, N80Q, C90, T95, P110, Q125 och 13Cr
Höljesrör Storleksområde: 5 1/2 "till 20" Längd vanligtvis i R3.
Slang Rördimensioner: 1,0 ", 1,315", 1,66 ", 1,9", 2,063 ", 2 3/8", 3 1/2 "och 4 1 /2", längd i R2.
Typ av anslutningar för hölje: BTC (gänga kopplingsstöd), LTC (lång rund gänga koppling), premium anslutning.
Typer av anslutningar för slangar: BTC, NUE, EUE, Premium
FAQ
Vad är API-standarden för hölje?
Den primära API-standarden för hölje ärAPI Spec 5CT(Specifikation för hölje och rör).
Det är det branschövergripande-styrdokumentet som definierar de tekniska kraven för dimensioner, mekaniska egenskaper, stålkvaliteter och testmetoder för både hölje och rör som används i olje- och gaskällor.
Vad är API-toleransen för hölje?
EnligtAPI Spec 5CT, standardtillverkningstoleranserna för hölje är:
Ytterdiameter (OD):+1.00% / -0,50% av rörets nominella OD.
Väggtjocklek:Minsta väggtjocklek får inte vara mer än12,5 % lägreden nominella väggtjockleken (det finns ingen specificerad övre gräns för väggtjocklek, förutsatt att viktkraven är uppfyllda).
Vikt:+6.5% / -3,5% per enskild led.
Rakhet:I allmänhet bör den totala avvikelsen inte överstiga0.2%av den totala rörlängden.
Vilka är de tre vanliga slangstorlekarna som används?
De tre vanligaste API-slangstorlekarna som används inom olje- och gasindustrin är:2-3/8 tum(60,3 mm),2-7/8 tum(73,0 mm),3-1/2 tum(88,9 mm).







